Cycle Stop Valves
Constant Pressure Pump Control Valves
Home Products Animations Forum FAQ Order Online


Reviews
CSV Applications
Product Catalog
Print Literature
Well and Pump Basic Info
VFD Does Not Save Energy
CSV vs VFD
CSV Tech. Info
WQA Certified
Calculators
Tank Sizing
Pump & Motor Manufacturers
Letters to Editor
Retrofits
Pressure Switch
Event Calendar
Warranty Info
About Us
Replace Mono Drive or Sub Drive with CSV



The Mono Drive is a single-phase drive and the Sub Drive is a three phase drive. Only difference between these and most other drives is that they now use a go/no go switch instead of a pressure transducer but, the effect on the power consumption is relatively the same. Systems with pressure transducers can be slow reacting and not very reliable, usually sticking in the full speed position. So the go/no go switch solved some of the slow reaction problems but, caused a few others. I was told that Mono and Sub drive units are made to vary the flow rate of a pump for intermittent use only. Taking a shower or filling a washing machine is considered intermittent usage. Any long-term water uses such as heat pumps and irrigation needs to be matched to the max output of the pump. When you are using low flow rates the amps are bobbing up and down 45 times per minute between say 2.6 and 3.2 amps. This is showing you that the (go/no go) switch used with the Mono Drive instead of a pressure transducer is causing the pump to ramp up and down about 45 times per minute. Then once per minute the unit does a "bump" as Franklin calls it, which increases the pressure about 4 PSI and completely shuts off the pump/motor. Then because water is still being used the pressure quickly drops and the pump restarts after only a couple of seconds. With a Mono or Sub Drive this process is repeated over and over as long as the flow required is less than the max output of the pump. When you are using maximum flow the amps stay steady. That is because this is the only amount of water that the pump is "designed" to pump for any long-term water use. The continuous bouncing and weaving is just how it maintains the speed required for low flows.

What I am hearing and seeing in the field is that the continuous ramping up and down of the Mono Drive and Sub Drive controlled pumps is causing the wire down hole to wear out quickly and even wearing holes in the side of the pump or motor from touching the casing. This motor torque is happening 45 times per minute, which is a million times every 21 days of use. I am also hearing that the fan in the Mono Drive needed to cool the electronics is drawing in lint and other debris, which reduces the airflow and causes overheating of the Drive itself. Not to mention the ones I have heard about that where destroyed from this airflow area being taken over by fire ants and other critters. Then there is the "stray voltage" caused by the Mono Drive or any VFD. Do a search for "VFD stray voltage" and it will give you other problems to worry about. If you have to purchase a new pump/motor and or Mono Drive every 2 or 3 years, energy consumption is the least of your worries. If your pump system last 15 or 20 years as it should, you can afford to use considerably more energy and still be better off. Save 10 bucks a month on energy and spend $1,000.00 on a new pump every 2 years, or pay 10 bucks more a month for energy and have that $1,000.00 pump system last 20 years, do the math. Even if the VFD can save $10.00 per month in energy, considerably more money would be saved from the pump simply lasting longer. The actual amount of energy saved by a VFD if any, is closer to $3.00 per month on average, which makes saving energy even less important than pump system longevity.

The problem with any variable speed control is that you lose head by the square of the speed, so you can't slow it down enough that saving energy by the cube of the speed makes any difference. In other words the power consumption between a regular full speed pump and a variable speed pump is basically the same. Lift or pressure required from a well pump or booster pump is constant, so it can't even lift water out of the well if it is slowed down enough to save energy. Simply restricting the water from a regular pump with a valve will reduce power consumption as much as a VFD.

All a Cycle Stop Valve or CSV does is restrict the flow from a normal full speed pump to match the amount of water you are using. The CSV basically mimics much of the way a VFD pump works but, will triple or quadruple the life of a pump system compared to a VFD. There are many advantages to using a CSV instead of a VFD. A few of which include:
* Same constant pressure as a VFD
* Being able to use a normal full speed pump
* Regular pressure switch and small tank so pump does not start for the ice maker or single glass
* Cost less and makes pumps last longer

Cycle Stop Valve verses Constant Pressure Pump video
http://www.cyclestopvalves.com/video/constant-pressure-pumps-vs-csv-dsl.wmv



Cycle Stop Valves® is a registered trademark.
All right reserved unless prior authorization is obtained.
Cycle Stop Valves, Inc.
10221 CR 6900
Lubbock, Texas 79407
Send Email
800-652-0207
Fax: 806-885-1994